See below for detailed information about adding borders to your quilt. The sections include:

      Piecing Border Strips

      Overlapped Borders

      Mitered Borders


Whenever possible purchase enough fabric to cut borders on the lengthwise grain (parallel to the selvage edge). It is the strongest grain and will help to prevent stretching and fullness along the outer edges of the quilt. When you must piece border strips, sew together with a 45 degree angled seam. The diagonal seam will be less noticeable than a straight seam.

Step 1. Begin by layering right sides of fabric together, overlapping as shown in Diagram I.

Step 2.  Draw 45 degree angle line from top left to bottom right. Use points where strips crossover as guide for drawing line.

Step 3.  Sew directly on top of line.

Piecing Binding

Diagram I

  Step 4. Cut away excess fabric leaving a 1/4" seam allowance. Press to one side.

Piecing Strips Diagram 2



Step 1. Before cutting border strips, measure the quilt top vertically, along each side, and in the middle. Add these three measurements together and divide by three. The averaged number is the length for the side border strips. Cut border strips desired width, using length according to averaged measurement. Need help cutting strips? Link to "Rotary Cutting" lessons page.

Measuring Quilt Top

Step 2. Mark center on each strip and on each side of the quilt top. Match center marks. Align and pin end of strip with each corner edge of quilt top. Pin layers together, easing in any fullness. Sew strips to top.

Step 3. Repeat measuring, pinning and sewing steps for the top and bottom border strips.

Step 4. Repeat Steps 1-3 for additional borders. When finished, the quilt top will be squared with any fullness located within the patchwork area. Normally the quilting process will eliminate the fullness. This method will help to eliminate a rippling effect in the borders.

Attaching Border Strips



Miter border corners when an angled seam complements the overall design of the quilt. For multiple borders, sew strips together first and attach to quilt as one unit.

Step 1. Cut 2 strips the width of the quilt plus twice the border width and 2" inches extra and 2 strips the length of the quilt plus twice the border width and 2" inches extra.

Example: Width of quilt before border = 65"; width of border(s) to be added = 6"

65" + 6" + 6" + 2" = strip 79" long. Cut 2 strips 79" long (width measurement).

Repeat steps for length of quilt.

Step 2. Center and pin border strips in place. Start and end seams 1/4" from raw edges: backstitch to secure. Press seams toward quilt top.

Step 2 Diagram

Step 3. Lay quilt top right side up on ironing board and fold each border end flat back onto itself, right sides together, forming a 45 degree angle at the quilt's corner. Press to form sharp creases.

Step 3 Diagram

Step 4. Fold quilt on diagonal, right sides together. Align border strip raw edges, border seams at the 1/4" backstitched point, and creases; pin in place. Stitch along crease, backstitching at 1/4" border seam.

Step 4 Diagram

Step 5. Press seam open. With quilt right side up, align 45 degree angle line of square ruler on seam line to check accuracy. If corner is flat and square, trim excess fabric to 1/4" seam allowance.

Post a comment
To comment on this article you must be logged in. Not a member?


I goofed the first try, but immediately saw my mistake and did all four corners successfully! Thank you! Whew! :o)
Mitered borders
thanks sooooo much, very easy to understand and I got great results !
mitered border
am working on 'the quilt from ____" with very poorly written directions; these mitered border directions were very clear; thank you
Mitered Corners
Your instructions for mitered corners are clear and consice; thank you; this was the third reference pt I went to, and the only one that made sense!
McCall quilt lessons
Very clear instructions, especially for a new quilter. Thank you, I use it often. Allore
McCalls Quilt Lessons
Love this site!! Anytime I have a questions on how to do something, this is the first place I look. Check out Bias Binding as well!


Forgot password?
© F+W All rights reserved.